Posts Tagged ‘Problems’
Many people run into the problem of having there motion light sensor being too sensitive. Sometimes this issue can be resolved with nothing more then a good cleaning. Take a clean cotton cloth and use acetone to wipe down the electric eye or sensor. While you’re at it clean the surface of the light as well. Think about the location of your unit and the range of vision within the eyes scope. Is there a street nearby that could be visible within the peripheral vision of your motion sensor light? A lot of the time we underestimate the range of radar, which is the science behind the technology that makes a motion sensor work.
A good tip for limiting unwanted motion being picked up is to use electrical tape or some other type of tape and tape the sides of the sensor so the area to be avoided is removed from the unit’s field of vision so to speak. This can be good if there’s a public sidewalk near your home to avoid setting it off when people walk by. You may ultimately have to relocate the sensor for some applications. Units are available with remote sensors that can be placed away from the actual lighting unit. This may be an answer for long walks or driveways. They can be used to illuminate the drive as you enter and control lights all the way to your door.
One other rather drastic trick is to use a can of black spay paint and fog the sensor. Use a short blast far in front of the unit until it’s barely visible on the lens. try the light out and add another dusting if it’s still too sensitive. This is a trial and error method and may not work for all units.
Resetting the unit will sometimes help to get your lights back to the default settings. There is usually a test or reset button somewhere on the light. Press the button and then try out your lights again. If your lights are not coming on make sure to check any breakers at the power source as well. If your lights are located in an unprotected exterior location then it’s a possibility that water has gotten into the unit. It’s recommended that you replace the unit with a new one, instead of trying to repair it. There is a potential for a fire risk and personal injury or property damage could be caused by a defective or damaged motion sensor light.
Most of these units are made very inexpensively and getting a good one means buying the top of the line. Sometimes an electrical surge can be the culprit of a faulty sensor. Too much power can overload the tiny circuitry used with motion sensor lights. If this is the case, fifty percent of the time it will pop the reset. The rest of the time it can burn the connections and cause the sensor to have false readings.
If all else fails with motion sensor lights too sensitive, you’ll need to replace your outdoor motion sensor lights. Fortunately they are relatively inexpensive and well worth the comfort they add to your life. Security safety and a good night’s sleep don’t usually come in this cheap of a package.
Here Are A Few More Articles That May Help
Motion Sensor Problems – My Outdoor Motion Sensor Light Stopped Working, is an article that will take you through the possible problems you may be having and offer you some solutions. When you’re having motion sensor problems, your lights may be coming on when you don’t want them to. They could also be failing to come on when they should. Your timer may not be working, or maybe the problem is, they only work on test mode. Or possibly yours won’t shut off in the daytime.
In order to resolve the issue, let’s take a few seconds to discuss just how a motion detector is supposed to work. Normal operation uses a few simple components and knowledge of these parts will make it easier for you to troubleshoot your motion detectors. Motion detectors use a form of radar to detect movement in the form of heat, or temperature through infrared sensors that send out a wave and measure the time it takes for the wave to return. When something interferes with the rate of return, the motion detector is activated and the switch turns on. This can be a human or animal or even a leaf blowing by. It can be cars passing in the street or even a piece of trash blowing into the range of the detector. After a set period of time without the wave being interrupted, the switch will turn off. This time period is user adjustable and usually ranges from one minute to twenty minutes depending upon the manufacturer. Motion detectors also incorporate a photocell switch. This component detects sunlight and actually breaks the circuit for the infrared detector during daylight hours. This keeps your lights from coming on during the day when they would be wasting valuable energy.
Motion detectors need a power source. This can be an electrical connection to your homes power supply, or a solar source, or even a battery. No matter what your unit uses to get its power, the troubleshooting procedures and the solutions are all the same.
- If your motion lights will not come on, first check the bulbs by trying the lights on test mode. The lights should come on and stay on. Test mode allows you to try the unit out in the daytime as well.
- Check the power supply and make sure the breaker is on and that no secondary switch has been inadvertently turned off. Check the battery if you have a battery unit. Solar units must be dirt free and not obstructed from sunlight by leaves or other debris.
- Exterior motion lights should be sealed from possible moisture. This could be an issue if the fixture is turned upward and water collects within the socket. Make sure to angle sockets down, even though most lights have water seals.
- If your lights are not shutting off, or coming on during daylight hours, the culprit is probably the photocell. If it’s not detecting sunlight, many different types of malfunctions can occur.
- Most motion detector lights are relatively inexpensive. Aside from changing light bulbs, replacing the entire unit may prove cheaper then repairing or replacing a single component.
When having motion sensor problems and your outdoor motion sensor light stops working, running through these fixes should find the problem 99 percent of the time. The other one percent of the time will prove to be a faulty unit.